View FSTU162211_294389.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Preliminary
FSTU162211 24-Bit Bus Switch with -2V Undershoot Protection and 25 Series Resistors in Outputs (Preliminary)
June 2001 Revised June 2001
FSTU162211 24-Bit Bus Switch with -2V Undershoot Protection and 25 Series Resistors in Outputs (Preliminary)
General Description
The Fairchild Switch FSTU162211 provides 24-bits of highspeed CMOS TTL-compatible bus switching. The low On Resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. The device is organized as a 12-bit or 24-bit bus switch. When OE1 is LOW, the switch is ON and Port 1A is connected to Port 1B. When OE2 is LOW, Port 2A is connected to Port 2B. The A and B Ports are protected against undershoot to support an extended range to 2.0V below ground. Fairchild's integrated Undershoot Hardened Circuit (UHC) senses undershoot at the I/O and responds by preventing voltage differentials from developing and turning the switch on. The FSTU162211 has equivalent 25 series resistors to reduce signal-reflection noise, eliminating the need for external terminating resistors.
Features
s Undershoot hardened to -2V (A and B Ports) s Slower output enable times to prevent signal disruption s 25 switch connection between two ports s Minimal propagation delay through the switch s Low lCC s Zero bounce in flow-through mode s Control inputs compatible with TTL level s See Applications Note AN-5008 for details
Ordering Code:
Order Number FSTU162211MTD Package Number MTD56 Package Description 56-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide
Devices also available in Tape and Reel. Specify by appending the suffix letter "X" to the ordering code.
UHC is a trademark of Fairchild Semiconductor Corporation.
(c) 2001 Fairchild Semiconductor Corporation
DS500064
www.fairchildsemi.com
Preliminary FSTU162211 Logic Diagram Connection Diagram
Truth Table
Inputs OE1 L L H H OE2 L H L H Inputs/Outputs 1A, 1B 1A = 1B 1A = 1B Z Z 2A, 2B 2A = 2B Z 2A = 2B Z
Pin Descriptions
Pin Name OE1, OE2 1A, 2A 1B, 2B NC Description Bus Switch Enables Bus A Bus B No Connect
www.fairchildsemi.com
2
Preliminary
FSTU162211
Absolute Maximum Ratings(Note 1)
Supply Voltage (VCC) DC Switch Voltage (VS) (Note 2) DC Input Control Pin Voltage (VIN) (Note 3) DC Input Diode Current (lIK) VIN < 0V DC Output Current (IOUT) DC VCC/GND Current (ICC/IGND) Storage Temperature Range (TSTG)
-0.5V to +7.0V -0.5V to +7.0V -0.5V to +7.0V -50 mA
128 mA
Recommended Operating Conditions (Note 4)
Power Supply Operating (VCC) Input Voltage (VIN) Output Voltage (VOUT) Input Rise and Fall Time (tr, tf) Switch Control Input Switch I/O Free Air Operating Temperature (TA) 0 ns/V to 5 ns/V 0 ns/V to DC -40 C to +85 C 4.0V to 5.5V 0V to 5.5V 0V to 5.5V
+/- 100 mA -65C to +150 C
Note 1: The "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum rating. The "Recommended Operating Conditions" table will define the conditions for actual device operation. Note 2: VS is the voltage observed/applied at either the A or B Ports across the switch. Note 3: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 4: Unused control inputs must be held HIGH or LOW. They may not float.
DC Electrical Characteristics
Symbol VIK VIH VIL II IOZ RON Parameter Clamp Diode Voltage HIGH Level Input Voltage LOW Level Input Voltage Input Leakage Current OFF-STATE Leakage Current Switch On Resistance (Note 6) VCC (V) 4.5 4.0-5.5 4.0-5.5 5.5 0 5.5 4.5 4.5 4.5 4.0 ICC ICC VIKU Quiescent Supply Current Increase in ICC per Input Voltage Undershoot 5.5 5.5 5.5 20 20 20 20 26 27 28 30 2.0 0.8 1.0 10 1.0 38 40 48 48 3 2.5 -2.0 TA = -40 C to +85 C Min Typ (Note 5) Max -1.2 Units V V V A A A A mA V 0 VIN 5.5V VIN = 5.5V 0 A, B VCC VIN = 0V, IIN = 64 mA VIN = 0V, IIN = 30 mA VIN = 2.4V, IIN = 15 mA VIN = 2.4V, IIN = 15 mA VIN = VCC or GND, IOUT = 0 One Input at 3.4V Other Inputs at VCC or GND 0.0 mA IIN -50 mA OE1,2 = 5.5v
Note 5: Typical values are at VCC = 5.0V and TA = +25C Note 6: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the voltages on the two (A or B) pins.
Conditions IIN = -18 mA
3
www.fairchildsemi.com
Preliminary FSTU162211 AC Electrical Characteristics
TA = -40 C to +85 C, Symbol Parameter CL = 50pF, RU = RD = 500 VCC = 4.5 - 5.5V Min tPHL, tPLH tPZH, tPZL tPHZ, tPLZ Propagation Delay Bus to Bus (Note 7) Output Enable Time Output Disable Time 1.5 1.5 Max 1.25 6.0 7.0 VCC = 4.0V Min Max 1.25 6.5 7.2 ns ns ns VI = OPEN VI = 7V for tPZL VI = OPEN for tPZH VI = 7V for tPLZ VI = OPEN for tPHZ Figures 2, 3 Figures 2, 3 Figures 2, 3 Units Conditions Figure Number
Note 7: This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical On Resistance of the switch and the 50pF load capacitance, when driven by an ideal voltage source (zero output impedance).
Capacitance
Symbol CIN CI/O
(Note 8)
Parameter Typ 3 6 Max Units pF pF Conditions VCC = 5.0V VCC, OE = 5.0V
Control Pin Input Capacitance Input/Output Capacitance
Note 8: TA = +25C, f = 1 MHz, Capacitance is characterized but not tested.
Undershoot Characteristic
Symbol VOUTU Parameter Output Voltage During Undershoot Min 2.5 Typ VOH - 0.3 Max Units V Conditions
Note 9: This test is intended to characterize the device's protective capabilities by maintaining output signal integrity during an input transient voltage undershoot event.
FIGURE 1.
Device Test Conditions
Parameter VIN R1 = R2 VTRI VCC Value see Waveform 100K 11.0 5.5 Units V V V
Transient Input Voltage (VIN) Waveform
www.fairchildsemi.com
4
Preliminary
FSTU162211
AC Loading and Waveforms
Note: Input driven by 50 source terminated in 50 Note: C L includes load and stray capacitance Note: Input PRR = 1.0 MHz, tW = 500 ns
FIGURE 2. AC Test Circuit
FIGURE 3. AC Waveforms
5
www.fairchildsemi.com
Preliminary FSTU162211 24-Bit Bus Switch with -2V Undershoot Protection and 25 Series Resistors in Outputs (Preliminary) Physical Dimensions inches (millimeters) unless otherwise noted
56-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Package Number MTD56
Technology Description
The Fairchild Switch family derives from and embodies Fairchild's proven switch technology used for several years in its 74LVX3L384 (FST3384) bus switch product.
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 6 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com

▲Up To Search▲

Price & Availability of FSTU162211

	To Download FSTU162211 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .